In the process of using a vertical balancing machine for dynamic balance correction of disc-shaped rotors, it is sometimes found that the measured values of the vertical balancing machine are unstable and the value is 0; Many users do not know how to solve the problem, and contacting the manufacturer of the dynamic balancing machine for repair seems to be too troublesome. Continuing to use it is also afraid of such a situation happening again. The reason for encountering this problem is that many users have not received systematic training on machine operation and have not mastered basic troubleshooting methods. The technical master of Huake Zhichuang Dynamic Balancing Machine specially popularizes common faults and solutions of vertical balancing machines for everyone.
1、 The main reasons for the unstable measurement speed of vertical balancing machines are as follows:
1. The conveyor belt of the motor pulley is too loose
2. Sensor has no output signal
3. Aging of electrical measurement system components
4. The temperature production period exceeds the maximum working temperature of the material
2、 What should I do if the displayed data is 0 or very small? First of all, don't panic when the displayed data is 0 or very small, as this may not be a serious problem with the vertical balancing machine. If the data is 0 or very small, use a multimeter to measure. If the resistance value is abnormal, it needs to be replaced or repaired.
1. If the vertical balancing machine only shows a measured value once and never shows it again in the future, this can be ignored.
2. If the data of the vertical balancing machine is 0 or very small at least once a day, contact the balancing machine manufacturer for the problem that occurs.
3. If the unstable data prevents normal operation, you can try to recalibrate the rotor first.
3、 Solution to vertical balancing machine malfunction
1. It is possible that the motor rotor shaft is eccentric or bent, resulting in excessive measurement error and inability to accurately find the balance angle.
2. Check if there is dirt on the surface of the fixture, which may cause imbalance when the fan blades rotate.
3. Whether the fixed top bracket is locked tightly or the support bracket is loose can cause unstable signal input in the balance machine measurement system.
4. Drive belt too tight
5. The measured speed exceeds the dynamic balance parameter speed.
The above content is a complete introduction to the analysis of the reasons and solutions for the problem of large measurement errors and zero data in vertical balancing machines. It is hoped that it will be helpful to users, and it is also hoped that the operators of dynamic balancing machines will have a good mood and good health every day.
1、 The main reasons for the unstable measurement speed of vertical balancing machines are as follows:
1. The conveyor belt of the motor pulley is too loose
2. Sensor has no output signal
3. Aging of electrical measurement system components
4. The temperature production period exceeds the maximum working temperature of the material
2、 What should I do if the displayed data is 0 or very small? First of all, don't panic when the displayed data is 0 or very small, as this may not be a serious problem with the vertical balancing machine. If the data is 0 or very small, use a multimeter to measure. If the resistance value is abnormal, it needs to be replaced or repaired.
1. If the vertical balancing machine only shows a measured value once and never shows it again in the future, this can be ignored.
2. If the data of the vertical balancing machine is 0 or very small at least once a day, contact the balancing machine manufacturer for the problem that occurs.
3. If the unstable data prevents normal operation, you can try to recalibrate the rotor first.
3、 Solution to vertical balancing machine malfunction
1. It is possible that the motor rotor shaft is eccentric or bent, resulting in excessive measurement error and inability to accurately find the balance angle.
2. Check if there is dirt on the surface of the fixture, which may cause imbalance when the fan blades rotate.
3. Whether the fixed top bracket is locked tightly or the support bracket is loose can cause unstable signal input in the balance machine measurement system.
4. Drive belt too tight
5. The measured speed exceeds the dynamic balance parameter speed.
The above content is a complete introduction to the analysis of the reasons and solutions for the problem of large measurement errors and zero data in vertical balancing machines. It is hoped that it will be helpful to users, and it is also hoped that the operators of dynamic balancing machines will have a good mood and good health every day.
107 browse